How to Print HueForge Without an AMS in Bambu Studio
Manual filament swaps on an A1, A1 mini or P1S: match the layers, add a pause at each swap height, change the spool and resume.
Yes, you can print HueForge without an AMS. HueForge itself says standard prints work on any FDM printer that can pause for a filament change, and the software is built to keep the number of swaps manageable. On a Bambu Lab A1, A1 mini or P1S without an AMS, that means adding a pause at each colour change in Bambu Studio, swapping the spool by hand when the printer stops, and pressing resume.
This guide is for anyone with a single-spool Bambu setup who has a HueForge STL (or a HueForge model from MakerWorld) and wants to print it in four or five colours anyway. It walks through the manual method first, then two shortcuts that do most of the work for you.
What you need before you slice
- The HueForge STL and the swap instructions that come with it. When you export from HueForge you get the model plus a describe file (a .txt) listing the starting colour and the height of every swap.
- If you’re printing someone else’s model, the swap list is usually in the description or the print profile notes on MakerWorld or Printables.
- Your filaments in the order the list asks for, ideally already dried and on hand. The print sits waiting while you swap, so you don’t want to go looking for a spool.
- Bambu Studio, and the printer’s external spool holder loaded with the first colour.
The swap list looks something like this, taken from a HueForge model on MakerWorld (opens in a new tab) that ships with a no-AMS profile: start with black, at layer 5 (0.48 mm) swap to grey, at layer 9 (0.8 mm) swap to white for the rest. Every swap is one pause, so a four-colour print with one swap per colour needs three pauses.
Step 1: Match the layer settings to HueForge
This is the step that quietly ruins prints. HueForge calculates its colour transitions for a specific first layer and layer height, and the HueForge FAQ (opens in a new tab) says the slicer has to use the same base layer and layer height as the project. If HueForge used a 0.16 mm base and 0.08 mm layers, set exactly that in Bambu Studio, otherwise your swap heights won’t land on real layers.
Import the STL, pick your printer and filament profile, set the first layer height and layer height under Quality, and leave the plate in a single filament. Bambu Studio will show the whole model in one colour, and that’s fine. The colours come from the pauses, not from the slicer preview.
Step 2: Add a pause at each swap height
Click Slice plate. Then use the layer slider on the right of the preview. Drag it, or use the arrow keys, until the label shows the first swap height from your list. Right-click the + icon on the slider and choose Add Pause. Bambu Lab’s guide to the slicing preview (opens in a new tab) explains that the printer pauses before it prints that layer and waits for you to resume it, so the layer you picked comes out in the new colour.
Repeat for every height in the list, then slice again. The swap heights are what matter. If the layer number in Bambu Studio doesn’t match the number in the describe file, go by the height in millimetres.
| Swap list says | What you do in Bambu Studio | At the printer |
|---|---|---|
| Start with black | Load black on the external spool | Start the print |
| Layer 5 (0.48 mm): grey | Add Pause on the 0.48 mm layer | Unload black, load grey, resume |
| Layer 9 (0.8 mm): white for the rest | Add Pause on the 0.8 mm layer | Unload grey, load white, resume |
If Add Pause is greyed out or the print button is disabled
- Check the print sequence. Bambu forum users report that pauses aren’t available when plates are set to print By object; switch it to By layer ( forum thread (opens in a new tab) ).
- If you added a Change Filament marker by mistake, delete it and add a pause instead, then slice again. Bambu Studio won’t send a single-spool plate with a filament change in it ( forum thread (opens in a new tab) ).
- To remove a pause, right-click the marker on the slider and delete it, then re-slice.
Step 3: Swap the filament when the printer stops
When the printer reaches a pause it stops and waits. On the A1 and A1 mini, Bambu Lab’s external spool guide (opens in a new tab) describes the swap: use Unload on the screen so the printer heats up and cuts the filament, pull the old filament out, then use Load to feed the new colour. Let it purge until the new colour comes out clean, then resume the print from the printer’s screen.
The swaps are short, but someone has to be there for them. If the first change happens a few minutes into the print, it’s worth staying close for the first layers rather than starting it and walking off.
Shortcut: Use a MakerWorld profile that already has the pauses
Many HueForge designers on MakerWorld upload a separate print profile labelled something like “NO AMS, pauses for manual filament swaps”, as on this model (opens in a new tab) and this one (opens in a new tab) . Open that profile in Bambu Studio and the pauses are already on the slider. Check the layer height and colour order against the notes before you print, and you’re done.
An advanced option some A1 owners use
On the Bambu Lab forum, one user shares a trick (opens in a new tab) for treating each colour change as a pause: copy the printer profile’s pause G-code into its “Change filament G-code” field and save it as a separate “No AMS” printer preset. You can then paint or assign colours as if you had an AMS and see them in the preview. The poster notes the limits: it was tested on an A1, the printer doesn’t switch to the new filament’s settings, so it suits filaments that print alike, such as PLA to PLA. Editing printer G-code is at your own risk, and for HueForge the plain pause method above does the same job.
Getting more out of fewer swaps
Without an AMS, every extra colour is another trip to the printer, so it pays to pick a palette that blends well. HueForge’s own advice is to use the Slicer View in the software to check that what you’ll print matches the preview. Your filament choice matters as much as the colour count, because HueForge relies on each filament’s TD (transmission distance) value to blend layers. We cover which filaments are worth buying first in the HueForge filaments I wish I had bought first.
And if you’re wondering whether a HueForge print counts as your own work when you share it, we wrote about that line in original 3D printing versus click-print.
I’ve also been printing two-view anime agamographs on a Bambu X2D, a different kind of multi-colour plate that changes as you walk past it.
Verification
Sources
- HueForge FAQ (opens in a new tab) — HueForge
- View slicing information in Bambu Studio (opens in a new tab) — Bambu Lab Wiki
- First print with external spool (A1 mini) (opens in a new tab) — Bambu Lab Wiki
- A1 mini FAQ (opens in a new tab) — Bambu Lab Wiki
- I can't insert a stop in a print (opens in a new tab) — Bambu Lab Community Forum
- A1 without AMS doesn't pause for a filament swap (opens in a new tab) — Bambu Lab Community Forum
- Multicolor prints without AMS, the easy(ish) way (opens in a new tab) — Bambu Lab Community Forum
- HueForge model with a no-AMS print profile (opens in a new tab) — MakerWorld
- HueForge model with a no-AMS print profile (opens in a new tab) — MakerWorld
Published 2 November 2026